16 Zone Fire Alarm Control Panel แบบ 24 Volt, 4/8/16 Zone Class B Conventional Fire Alarm Control Panel ออกแบบมาตรงตามความต้องการ ของผู้ใช้งานและ ULC codes
รองรับงาน ขนาดเล็ก ถึงกลาง อาคาร ขนาด 16 โซน
Advantage
- คุณภาพ ได้ตรงตามมาตรฐาน UL864 และ EN-54 standard
- มี Autmatic mode และ Manaul Mode ให้เลือก ใช้
- มี ฟังก์ชั่น circuit self-check ตรวจเช็คกรณีสายขาด ที่เซนเซอร์โซน และ Alarm Bell
- ติดตั้งง่าย สำหรับ ช่างติดตั้ง ใช้งานง่าย สำหรับ ผู้ดูแลระบบ
- ขนาดกระทัดรัด 320×260×80mm (length × width × depth)
INSTALLATION GUIDE
1000 Series รองรับการเชื่อมต่อ กับ Repeater หรือ Graphic annunciator (อุปกรณ์เสริม)
รูปแบบการเชื่อมต่อตามรูปด้านล่าง
ตัวควบคุม Fire alarm รองรับเชื่อมต่อ กับ Repeater ได้ถึง 32 ตัว
Repeater
เป็น Indicator Interface สำหรับแสดงผล สถานะการทำงาน เมื่อเกิด เหตุ Alarm หรือ False
ติดตั้ง ในห้องที่ ต้องการ Monitor
Repeater เชื่อมต่อ ออกมาจาก ชุดควบคุมหลัก Fire alarm control ผ่าน RS 485 ,
ผู้ใช้ สามารถ ติดอุปกรณ์ Repeater ได้ ตามห้องต่างๆ สูงถึง 32 ตัว
การทำงาน
สถานะ การทำงาน บนหน้ากล่อง Repeater จะแสดงผลเหมือนกับ หน้าตู้ Fire alarm control panel
อาทิ : เมื่อเกิดเหตุ Zone 4 Alarm
ที่หน้าตู้ Fire alarm control จะแสดง สถานะ Zone 4 alarm จากนั้น ตัว Repeater ก็จะ แสดงผล
โชว์ Zone4 alarm
----------------------------------------------------------------------------
การประยุกต์ใช้งาน
ระบบ Fire alarm with SMS Alert
---------------------------------------------------------------------------
Characteristics
4/8/16 Style B (Class B) Initiating Device Circuits (IDCs).
– All zones accept two-wire smoke detectors and any normally-open contact devices.
– Zones 1 – 4/8/16 configured as general alarm zones.
All circuits are power-limited and supervised, meeting the latest ULC requirements using
fuseless technology.
Two built-in, Style Y (Class B) Notification Appliance (Signal) Circuits (NACs).
NACs may be programmed:
– Silenceable
– Non-Silenceable.
– Auto-Silence (program 5 to 20 minutes)
1.25 amps of NAC power
3.0 amps of total system power
Alarm, Trouble and Supervisory, Form-C relays standard.
24-volt operation
Resettable four-wire smoke detector power @ 500 Ma
Non-resettable power @ 500 mA.
Integral battery charger capable of charging up to 18 AH batteries (batteries over 4 AH
require use of the external battery backbox, or ULC listed equivalent).
One-man walk-test programmable for silent or audible test.
Disable/Enable control per IDC
Reverse polarity protection
Control buttons:
– Mode
– Test
– ACK (Acknowledge) Alarm Silence
– Reset
Meet UL864, EN-54 standard.
LED indicators:
– AC Power (green & yellow LED)
– Fire Alarm (red LED)
– Trouble (yellow LED)
– Supervisory (yellow LED)
– Signal Silence (yellow LED)
– Battery Power (green & yellow LED)
– Zone Disable (yellow LED)
– NAC Fault (yellow LED)
– NAC Disable (yellow LED)
– 4/8/16 Zone Alarm (one for each zone) (red LED)
– 4/8/16 Zone Trouble (one for each zone) (yellow LED)
– Earth Fault (on circuit board)
– Battery Fault (on circuit board)
– Charger Fault (on circuit board)
Specifications
AC Power: AC220V±10% 50Hz, 2.0 amps, minimum 14 AWG wire (2.0 mm²) with 600-volt insulation.
Battery: Sealed lead-acid batteries only, Maximum charging circuit: 27.6VDC @ 0.8 amp for normal flat
charge, Maximum battery charger capacity: 18AH battery
NOTE: two 4AH batteries can be housed in the cabinet. Larger batteries require a separate battery box.
Total 24 V system power: 3.0 amps
Notification appliance (signal) power: 2.5 amps
Maximum current per NAC: 1.25 amps (expandable to 2.5 amps)
Auxiliary Outputs: – Resettable four-wire smoke detector power @ 500 mA
– Non-resettable power @ 500 mA
– Integral Form-C Alarm, Trouble and Supervisory relays, rated at: 2.0 amps @ 30
VDC (resistive), 2.0 amps @ 30 VAC (resistive).
NOTE: Total current for auxiliary power outputs and two NACs must not exceed 3.0 amps.
Using environment: Temperature: 0°C~50°C Related Humidity: ≤95% (40±2°C)
Dimensions: 320×260×80mm (length × width × depth)
-------------------------------------------------------------------------------------
เชื่อมต่อ ตัวแสดงผล Graphic Annunciator